A T-6 texan pilot inadvertently unlocked the tailwheel during landing when he applied too much forwa...

Narrative:

Second flight of the day for formation training following fast formation practices. Three T-6 aircraft were participating in the training. My T-6 was the number two ship in a flight of three ships. We were landing after performing an overhead 360 approach to landing. I had touched down on the right side of the center line (lead touched down on the left side). I wheeled landed and was keeping the a/c on the main gear until the 2000 foot remaining mark. I then let the tail come down. The airplane felt light on the main gear and started to lift and divert to the right. I added power and left rudder for directional control. The airplane left the runway for the grass on the right side then went right wing high and started to divert left. I closed the throttle and attempted to regain directional control and bleed of speed and energy. During this entire roll out; the tail wheel felt that is was not locked. I initially though the locking pin sheared and I only had rudder for directional control. I managed to get the a/c back onto the runway and stopped after swerving left and right until stopped. Once stopped; I shut down the engine and got out to inspect the tail wheel and the a/c. It was obviously not locked. There was evidence that the aft portion of the left wing tip and aileron came into contact with the grass while the a/c was off of the runway. The airport manager closed the runway until we were clear of the runway. This was about 30 minutes duration. With the help of a mechanic; we removed the fairing and saw the locking pin was intact and we were able to move the tail wheel into the locked position. Started the engine and taxied to the hangar for further inspection. The tail wheel would lock and unlock without difficulty. Remained locked during the taxiing to parking. It is suspected that I inadvertently unlocked the tail wheel during roll out by applying too much forward pressure and also let the tail settle with too much forward speed. This cause the float and unloading of the main gear. The damage was determined by several mechanics not to an airworthiness issue and the airplane was returned to service and flow back to the airport it is based at without incident.

Original NASA ASRS Text

Title: A T-6 Texan Pilot inadvertently unlocked the tailwheel during landing when he applied too much forward pressure causing the aircraft to leave the runway. During one of the off runway turns a wingtip struck the grass.

Narrative: Second flight of the day for formation training following FAST formation practices. Three T-6 aircraft were participating in the training. My T-6 was the number two ship in a flight of three ships. We were landing after performing an overhead 360 approach to landing. I had touched down on the right side of the center line (lead touched down on the left side). I wheeled landed and was keeping the a/c on the main gear until the 2000 foot remaining mark. I then let the tail come down. The airplane felt light on the main gear and started to lift and divert to the right. I added power and left rudder for directional control. The airplane left the runway for the grass on the right side then went right wing high and started to divert left. I closed the throttle and attempted to regain directional control and bleed of speed and energy. During this entire roll out; the tail wheel felt that is was not locked. I initially though the locking pin sheared and I only had rudder for directional control. I managed to get the a/c back onto the runway and stopped after swerving left and right until stopped. Once stopped; I shut down the engine and got out to inspect the tail wheel and the a/c. It was obviously not locked. There was evidence that the aft portion of the left wing tip and aileron came into contact with the grass while the a/c was off of the runway. The airport manager closed the runway until we were clear of the runway. This was about 30 minutes duration. With the help of a mechanic; we removed the fairing and saw the locking pin was intact and we were able to move the tail wheel into the locked position. Started the engine and taxied to the hangar for further inspection. The Tail wheel would lock and unlock without difficulty. Remained locked during the taxiing to parking. It is suspected that I inadvertently unlocked the tail wheel during roll out by applying too much forward pressure and also let the tail settle with too much forward speed. This cause the float and unloading of the main gear. The damage was determined by several mechanics not to an airworthiness issue and the airplane was returned to service and flow back to the airport it is based at without incident.

Data retrieved from NASA's ASRS site and automatically converted to unabbreviated mixed upper/lowercase text. This report is for informational purposes with no guarantee of accuracy. See NASA's ASRS site for official report.

Attributes
ACN	1290725
Time
Date	201508
Local Time Of Day	1201-1800
Place
Locale Reference	ZZZ.Airport
State Reference	US
Environment
Flight Conditions	VMC
Light	Daylight
Aircraft 1
Make Model Name	Texan T6/Harvard (Antique)
Operating Under FAR Part	Part 91
Flight Phase	Landing
Route In Use	Visual Approach
Flight Plan	None
Component
Aircraft Component	Tail Wheel
Person 1
Function	Pilot Flying Single Pilot
Qualification	Flight Crew Instrument Flight Crew Private
Experience	Flight Crew Last 90 Days 30 Flight Crew Total 700 Flight Crew Type 200
Events
Anomaly	Deviation - Procedural Published Material / Policy Ground Event / Encounter Ground Strike - Aircraft Ground Excursion Runway

A T-6 texan pilot inadvertently unlocked the tailwheel during landing when he applied too much forward pressure causing the aircraft to leave the runway. During one of the off runway turns a wingtip struck the grass.